How do you run a diagnostic test on a Frigidaire Affinity washer?

VIDEO

.

Considering this, how do I find the error code on my Frigidaire Affinity washer?

Check the 5 pin connector wiring between the console control and the motor control. “do” or “dr” – door problem. “Err” – an error has been detected.

READING ERROR CODES:

1. Wake the washer by pressing any button.
2. Wait 5 seconds.
3. Press and HOLD the Start/Pause and Cancel buttons simultaneously.

Also, how do I troubleshoot my Frigidaire Affinity washer?

1. Stop the washing machine if rattling or clanking sounds occur.
2. Redistribute the load if you hear a thumping sound.
3. Level the washer if the machine vibrates.
4. Plug the power cord in and check household fuses or breakers.
5. Turn the water supply faucets on completely.
6. Wait for the washer to cool down.

Also, how do you run a diagnostic test on an Electrolux washing machine?

How to enter diagnostic/service mode in an Electrolux front loading washer. * Press the Cancel button to enter standby mode and enable diagnostic entry. * Within 10 seconds after pressing Cancel , press any button to wake up the control. button under the display simultaneously for 3 seconds to enter the diagnostic mode

How do I reset my Frigidaire washer?

How to Reset the Settings on a Frigidaire Front Washer

1. Verify that your Frigidaire front washer is plugged into a working electrical outlet and turned on; otherwise, you won't be able to reset it.
2. Press and hold the "Spin Speed" and "Soil Level" buttons together for a few seconds.
3. Continue holding the buttons until a signal sounds then release them.

Related Question Answers

Why does my Frigidaire Affinity washer keeps pausing?

The PAU, or pause, error usually means that the washing machine cycle was interrupted and was not restarted properly. If the washer was stopped midcycle and not restarted, the cycle must be canceled or completed before a new selection can be made.

Why is my washing machine drum not turning?

If your washer fills with water but doesn't agitate, the problem is likely to be a faulty lid switch, a broken belt, or a problem with the motor. 1 Check the washing machine's spin cycle. If this works, the motor is operating and the belt is not broken. If the spin cycle doesn't work, the belt may be loose or broken.

How do you reset a Frigidaire top load washer?

You can easily reset your Frigidaire washer.

1. Press the "Cancel" button on the washer's display.
2. Turn the knob or push the button to select a new cycle.
3. Press "Start." You have now reset your Frigidaire washer.

How do you reset a Frigidaire dryer?

The first thing to do when an error code appears on the Frigidaire dryer is to reset the unit. Press "Pause/Cancel" twice to cancel the current operation. Make a new dryer cycle selection and press and hold "Start." If the E68 error code comes back, press "Pause/Cancel" twice again.

What does e90 mean on a washing machine?

The error code E90 is just a group error code. It is indicating a communication error between the two boards in your machine. It does not indicate where the problem may be. A power glitch may have caused the E90 error code or a loose connection. One of the control boards could have failed.

How do you clear error codes on Frigidaire Affinity washer?

To clear latest stored error code: • Turn the Program Knob to the start position, Spin Only. Press Start/Pause to start the cycle and save it. Press Cancel to stop the cycle and turn off the LEDs. Press Cancel again to turn on the LEDs.

What does e4 mean on a Frigidaire washer?

Frigidaire FWAC16I3MSGKW Washer Error Codes

DISPLAY	CAUSES
E3	The lid is not close before spin.
E4	Alarm for shocking in the same spin process third times.
F8	Alarm for water level sensor.
C9	When the communication failure.

How do you fix a Frigidaire Affinity Dryer?

How to Troubleshoot a Frigidaire Affinity Dryer

1. Listen for abnormal operating sounds. The Frigidaire Affinity dryer sounds different from a standard clothes dryer.
2. Check that the Affinity dryer has electrical power.
3. Set the Affinity dryer to the correct cycle.
4. Clean the lint filter regularly.
5. Latch the door securely before you start the drying cycle.

How do I reset my affinity washer?

I received the following fix that worked for my Affinity washer. Turn the washer display on by rotating the knob to any cycle, press and hold the spin speed and soil level buttons at the same time until the display reads 'Restore default'.

What does e10 mean on Frigidaire washing machine?

I am sorry you are having a problem with your washer. The E10 error code indicates the control does not see a proper fill. Here are a few things you can easily check.

How do I reset my washing machine?

To perform the Master Reset, carefully unplug the washing machine from the power outlet and leave it unplugged for one minute. After one minute is up, plug the washer cord back into the wall. Next, open and close the door of the washing machine 6 times within 12 seconds to send a “reset” signal to all the components.

What does e11 mean on Electrolux washer?

E11: Fill Time Too Long. E11. Water Tap closed, Water Flow Rate too low, Pressure Sensor defective, Inlet Valve. defective or Air Tube kinked.

How do you reset a Frigidaire washing machine?

A Frigidaire washer can be reset by pressing the cancel button located on the washer's display and turning the knob or pressing the button to select a new cycle. Pressing the start button finishes the reset of the washer.