Can you add a remote control to a gas fireplace?

A gas fireplace remote control will allow you to easily start your gas fireplace with the minimal effort of clicking a button. The installation of your remote is fairly simple and only requires a few materials. Take your receiver, which will get the signals from the remote control, and connect it to the gas valve.

.

In this regard, can you add a remote to a gas fireplace?

Yes, you can add a remote to your gas log set after it's been installed and the log set is already equipped with a millivolt valve. You may even be able to completely convert your gas log set to a remote control system with variable flame and thermostatic controls.

Likewise, can you put gas logs in a wood burning stove? Gas logs cannot be installed in wood burning stoves or gas burning stoves. Wood stoves are designed to use far less air than wood burning fireplaces, so in most cases they have a 6" diameter vent that is not enough to properly exhaust the fumes given off by gas logs.

Keeping this in consideration, how does a remote control gas fireplace work?

Many gas fireplaces operate with a remote control. In addition to an “On/Off” switch, the remote typically has a manual mode and a thermostat mode. When you operate the fireplace in manual mode, you set the temperature via the remote and it stays at that temperature until you turn off the fireplace.

How do I turn on my gas fireplace?

Turn the gas key. With the lighter activated, move the gas valve knob about half a turn counter-clockwise. This will release gas into the fireplace, causing the pilot light to ignite. Be prepared to move back quickly in case the fire ignites stray gas particles and flares out into the immediate surrounding area.

Related Question Answers

Why are my gas logs turning black?

The most common causes of soot buildup in a gas fireplace are ceramic fire-logs that have been moved out of proper position and burner ports that are clogged. The other main cause of soot is clogged ports on the gas burner, which causes an incomplete or unbalanced burn and formation of soot on the logs and doors.

When should gas fireplace logs be replaced?

However, embers do fade over time and will periodically need to be replaced. Embers can last up to five years depending on how frequently you use your fireplace. We have found that replacing embers every three years keeps a log set looking brilliant.

Are gas fireplace logs toxic?

Gas Log Fireplace Safety. Just like real burning logs, both types of gas logs produce carbon monoxide — a toxic gas that can be lethal — when they burn. Venting and proper use of a gas fireplace can help keep CO at a safe level.

What kind of logs do you use in a gas fireplace?

A vented gas log must be used in a regular fireplace, designed to burn a wood fire. Vent-free gas logs can be used in a regular fireplace or can be used in a prefabricated vent-free firebox that has no chimney. Some vented gas logs will give up to 25,000 BTU's of heat but most don't give hardly any heat.

How do I sync my fireplace remote?

Sync with the Remote Immediately following the beeps - press the "On" button on your remote control and hold it down for 1-2 seconds. This should produce 3 beeps from the receiver box to confirm it has captured the code from the remote control.

How does a fireplace switch work?

When the thermocouple is heated by the pilot light, it generates a very small electrical voltage (millivolts) which can be run through a switch to turn on a Milli-volt gas valve (as opposed to a 24 volt gas valve used with a conventional thermostat).

How do you arrange fake gas fireplace logs?

How to Arrange Gas Logs

1. Place the largest ceramic logs on the bottom to serve as the foundation for the fire.
2. Leave 2 inches (5 centimeters) between logs.
3. Make sure none of the logs is blocking the gas flow.
4. Arrange smaller logs on top of the foundation logs.
5. Turn on the gas and light the fire using either matches or the automatic igniter.

What is the fake wood in gas fireplaces made of?

ceramic

Do vented gas fireplaces smell?

Vented gas logs are burned in wood burning fireplaces with the damper fully open, so the smell that is produced goes up the fllue. So unless you have a poorly drafting fireplace, you will not have the odor problem described below if you install vented gas logs.

Can you install your own gas logs?

Gas log installation should only be done by a certified professional. Homeowners should never install their own gas logs unless they have the tools and training to do so.

How do you install a gas fireplace wall switch?

How to Install a Wall Switch to Gas Logs

1. Turn the control switch on the gas fireplace to the "Off" position.
2. Choose a convenient mounting location for the wall switch in accordance with the fireplace manufacturer's instructions.
3. Run a section of two-conductor, low-voltage wire from the single-gang box to the control panel of the gas fireplace.

Do gas logs require electricity?

If you have a gas fireplace with a vertical pilot, it will light during a power outage because it does not require electricity to start the pilot flame. If the gas fireplace has a blower or fan, it will need electricity, but you should still be able to generate heat without it.

Do you need logs in a gas fireplace?

Gas logs are not safe to install in a gas fireplace. It may sound odd, but it is entirely accurate. Though there are a few exceptions for some models of a gas fireplace, it is best to ask your contractor or the local professional. Gas logs are made to be installed in the wood burning fireplace.

What are ceramic logs?

Refractory ceramic gas logs are made of a mixture of cement and ceramic, which allows them to give off more heat than other types. They tend to last longer and are more durable than other options thanks to their ability to withstand very high temperatures. They can be used in both vented and ventless fireplaces.

How do gas fireplaces work?

The fireplace consists of incombustible "logs" covering gas vents, and the fire itself burns behind glass doors. The fire draws air outside air through a pipe to support combustion, so no warm room air is drawn out of the house. If you want to add a fireplace to an existing home, a gas fireplace makes sense.

What is a millivolt valve?

Millivolt Valve A millivolt gas valve is similar to an SPK, but instead of a thermocouple, a millivolt gas valve uses a thermopile. The thermopile generates a larger millivolt current than a thermocouple, allowing you to connect a hand-held remote, wall switch, timer, or thermostat to the gas log set.

Do you leave gas on in fireplace?

Are you sure? And no, we do not leave our direct-vent gas fireplace on when we're not in the room. "Vent free fireplaces are fireplaces that do not require any type of vent system. Instead, they are designed to burn clean and the combustion by-products allowed to flow into the room the fireplace is located in.

How do you start a gas fireplace for the first time?

If this is your first time lighting your gas fireplace, you should leave the knob pressed in for 30 seconds to bleed air out of the gas line. After waiting 5-30 seconds for the pilot light to be primed, and with the control knob still pressed in, click in the pilot ignition button located next to the control knob.

What is the fan for on a gas fireplace?

The fan draws cool air in from the bottom vents and heats it up inside before being forced out into the room at the top. Also known as heaters or fans, these fireplace inserts rely on a small, electronic motor to circulate warm air without adversely affecting the combustibility or strength of the fire.